Home › Metals we buy › Tungsten
Tungsten scrap, from heavy alloy blocks to carbide inserts
We buy tungsten scrap whether it is heavy alloy, pure tungsten or tungsten carbide, and the pickup is free anywhere in Southern California. Send a few photos and a rough weight through the quote form and we will quote your lot.

Heavy alloy, pure tungsten and carbide are not the same material
Pure tungsten is the element. The Royal Society of Chemistry gives it a density of 19.3 g/cm3 and a melting point of 3414 C.
Tungsten heavy alloy, under one definition in the defense acquisition rules (DFARS), is at least 90 percent tungsten in a matrix such as nickel-iron or nickel-copper, with a density of at least 16.5 g/cm3. A Sandia National Laboratories presentation of the ASTM B777 table lists four classes at nominal 90, 92.5, 95 and 97 percent tungsten by weight.
Tungsten carbide, also called cemented carbide or hardmetal, is the biggest use: USGS estimates that in 2025 about 60% of the tungsten consumed in the United States went into cemented carbide parts. The International Tungsten Industry Association (ITIA) describes a typical grade as 90% tungsten carbide and 10% cobalt.
Sources: Royal Society of Chemistry: tungsten; USGS Mineral Commodity Summaries 2026: tungsten; DFARS 252.225-7052 (tungsten heavy alloy definition); Sandia National Laboratories presentation of the ASTM B777 table (OSTI); ITIA: applications and markets.
Where tungsten scrap starts
Heavy alloy goes where a lot of weight has to fit in a small space: ASTM B777 names weights and counterbalances, radiation shielding and vibration damping among its uses. In its tungsten recycling study USGS says: "Most of the new scrap is in the form of high-quality turnings, but powders, floor sweeps, and solid scrap (rejected parts) are also generated."
Pure tungsten scrap comes from mills and parts makers, whose hard scrap USGS lists as sinter bar ends, rod and wire end trim, and rejected parts. Carbide scrap follows the cutting, since USGS says cemented carbide parts are used mainly in construction, metalworking, mining, and oil and gas drilling. Southern California does plenty of that metalworking: California EDD counted 53,000 jobs in aerospace product and parts manufacturing in Los Angeles County in September 2026.
Sources: ASTM B777 scope (ASTM); USGS Circular 1196-R: tungsten recycling in the United States in 2000; USGS Open-File Report 2005-1028: tungsten recycling; USGS Mineral Commodity Summaries 2026: tungsten; California EDD: Los Angeles County employment (CES).
The tungsten we buy, form by form
Solids are whole pieces; turnings are the chips a lathe or mill cuts off. We buy both, kept in separate containers:
- Heavy alloy: counterweights, shielding parts, bar and plate offcuts, and drained turnings in a drum of their own.
- Pure tungsten: rod and wire ends, sinter bar ends, sheet, electrodes and rejected parts.
- Carbide: inserts, solid end mills and drills, rods, dies and wear parts.
- Fines: grinding sludge, powder and floor sweeps, sealed.
USGS calls the solid pieces hard scrap and the sludge, powder, swarf and turnings soft scrap, and ITIA says most soft scrap goes to chemical recycling, so keep fines away from solids.
Pull out the high-speed steel. ITIA says it holds 1.5 to 20% tungsten and comes in the same tool shapes as carbide, drills, taps and milling cutters among them, but it is steel, and we do not buy iron or steel.
Sources: USGS Open-File Report 2005-1028: tungsten recycling; ITIA: recycling of tungsten, part 2 (2019); ITIA: tungsten in steel.
Weight first, magnet last
Every form of tungsten is far denser than iron, which NIST lists at 7.874 g/cm3:
| Material | g/cm3 | Against iron |
|---|---|---|
| Pure tungsten | 19.3 | about 2.5 times |
| Heavy alloy, ASTM B777 Classes 1 to 4 | 16.85 to 18.85 | about 2.1 to 2.4 times |
| Tungsten carbide | 15.6 | about 2 times |
| Carbide grades at 3.7% and 6.0% cobalt | 15.17 and 14.91 | about 1.9 times |
A scale will not always separate the heaviest carbide from the lightest heavy alloy, though.
A magnet is the weakest check. ASTM B777 says heavy alloys may contain elements that make them weakly ferromagnetic, and that Class 4 is not available in a non-magnetic grade; a 2011 study found its copper-bearing grade paramagnetic and two nickel-iron-based grades slightly magnetic. Pure tungsten is listed as paramagnetic, a response far weaker than iron's. If a drawing or certificate names the class, photograph it with the parts.
Sources: NIST: densities of the elements (X-ray attenuation tables); Royal Society of Chemistry: tungsten; Sandia National Laboratories presentation of the ASTM B777 table (OSTI); National Toxicology Program: cobalt-tungsten carbide profile; OSTI 2376169: densities of two carbide grades; ASTM B777 scope (ASTM); Kompozyty 11:3 (2011): magnetic properties of tungsten heavy alloys; HyperPhysics (Georgia State University): magnetic properties table; HyperPhysics (Georgia State University): magnetic properties.
What sets a tungsten scrap price
We quote each lot from its photos, form, alloy or grade, cleanliness and rough weight, not from a price list.
- Form. USGS says the zinc process for carbide needs sorted hard scrap with oil, solder and coatings removed, and ITIA says chemical recycling, the route for most soft scrap, takes more energy and chemicals than direct recycling.
- One material per container. Heavy alloy, pure tungsten and carbide kept apart are each quoted as themselves.
- Attachments. ITIA says carbide attached, brazed onto or cast into steel is the main reason recycling rates run lower in those groups; note how much steel rides on each piece.
- Cleanliness. Oil, coolant and water add weight that is not tungsten.
The market moves too. USGS reported that China put new export controls on selected tungsten items in February 2025 and that prices rose sharply through 2025, so we price your lot on the day instead of printing a number.
Sources: USGS Open-File Report 01-349; ITIA: recycling of tungsten, part 2 (2019); ITIA: recycling of tungsten, part 1 (2018); USGS Mineral Commodity Summaries 2026: tungsten.
Selling tungsten scrap to us, and what California asks
Send photos of the lot and a few pieces up close, a rough weight or drum count, and the city through the quote form, to help@socalscrapmetalbuyer.com, or call (562) 685-9090. Free pickup covers any Southern California county, such as Los Angeles, Orange, Riverside, San Bernardino, San Diego, Ventura or Imperial.
California defines junk as all ferrous and nonferrous scrap metals and alloys, and junk dealers and recyclers must record each purchase: the seller's name and ID, such as a driver's license, a description of the material and a statement of ownership, reported to police daily or by the next business day. Business and Professions Code 21608.5 adds stricter rules for nonferrous material, defined as copper, copper alloys, stainless steel or aluminum; that list does not name tungsten. More in the California scrap metal law guide.
Sources: California Attorney General Information Bulletin 2025-DLE-12; AB 1508, Chapter 531, Statutes of 2012 (Bus. & Prof. Code 21608.5).
Common questions
How is a tungsten carbide scrap price worked out?
By form, cleanliness and weight. Solid inserts and end mills kept apart from sludge, with coated and brazed pieces noted, are quoted as what they are.
Do you post a tungsten scrap price per pound?
No. Each form and condition is valued differently and the market moves, so we quote your lot from its photos.
Will a magnet tell me a heavy part is tungsten?
Not by itself. Some heavy alloy grades pull weakly and some do not, and pure tungsten barely reacts. The weight in your hand says more.
Do you buy high-speed steel drills and taps?
No. High-speed steel carries tungsten, but it is steel, and we do not buy iron or steel.
Keep reading

Molybdenum
Moly sheet, rod, TZM and furnace parts
See what we take
Tantalum and niobium
Refractory sheet, rod, wire and offcuts
See what we take
Cobalt alloys
Stellite and other cobalt-chrome scrap
See what we take
How to identify scrap metal
A magnet, your eyes and the weight in your hand
Read it
Keeping alloy scrap separate
For machine shops: bins, turnings and solids
Read it
California scrap metal law for sellers
ID, photos, thumbprints and the third-business-day rule
Read itHave metal to sell?
Send a few photos and a rough weight for a quote. Free pickup anywhere in Southern California. Every metal except iron and steel.