Call (562) 685-9090

Home › Guides › Keeping alloy scrap separate

Keeping superalloy scrap separate, from the machine to the pickup

By SoCal Scrap Metal Buyer · Updated

Superalloy scrap is quoted as what it is only when it stays what it is: one alloy per drum, solids apart from turnings, drained and labeled. This guide is for the machine shops and plants that cut Inconel, Waspaloy, Hastelloy, titanium and cobalt alloys, and it covers bins, drums, oil, labels and the one alloy with its own safety rules, beryllium copper.

Four drums of different metal turnings, silver, gold, blue and dark grey, kept apart in a machine shop

Why mixed alloys lose value

A superalloy is a recipe. USGS says superalloys keep most of their strength even after long exposure above 650 C (1,200 F), and usually combine chromium, cobalt, iron and nickel with smaller amounts of aluminum, molybdenum, niobium, tantalum, titanium and tungsten. The makers' datasheets show how far apart the recipes sit:

AlloyNominal composition, percent
Waspaloy (nickel base)nickel 58, chromium 19, cobalt 13.5, molybdenum 4.3, titanium 3, aluminum 1.5
Hastelloy X (nickel base)nickel 47, chromium 22, iron 18, molybdenum 9
Haynes 230 (nickel base)nickel 57, chromium 22, tungsten 14, molybdenum 2
Haynes 188 (cobalt base)cobalt 39, nickel 22, chromium 22, tungsten 14

A drum holding all four matches none of them. Kept apart, scrap can go back into its own alloy: USGS says that of the superalloy scrap processed worldwide in 1996, "about 70 percent was recycled into the same alloy, about 20 percent downgraded." For titanium, USGS says new scrap such as clippings, stampings and turnings is usually segregated by material specification and melted into a product with the desired chemistry. Alloy names on this page are trademarks of their owners, used only as the common names of the alloys.

Sources: USGS Circular 1196-Z: nickel recycling in the United States; Haynes International: Waspaloy datasheet; Haynes International: HASTELLOY X datasheet; Haynes International: HAYNES 230 datasheet; Haynes International: HAYNES 188 datasheet; USGS Circular 1196-A-M: metal recycling in the United States; USGS Circular 1196-Y: titanium recycling in the United States.

A labeled bin at every machine

Sorting costs least where the chip is made. Put a bin or a lidded drum at each machine that cuts exotics, mark it with the alloy on the spindle, and change the label when the job changes, so the second shift is not guessing.

Use the words the trade uses. ReMA's specifications, the scrap industry's common language for grades, recommend describing material by its code name or a clear description and stating any allowed variation, such as moisture. For an exotic alloy, a clear description is the alloy name or UNS number plus the form: Hastelloy X, UNS N06002, solids.

Gaylords, the pallet-sized cardboard boxes, suit clean solids. Turnings go in lidded drums, and grindings and sludge in their own sealed pails. A gaylord that collects every alloy in the building is the habit to break.

Sources: ReMA ISRI Specifications (July 2026); Haynes International: HASTELLOY X datasheet.

A steel tote of nickel superalloy scrap: machined rings, flanges and offcuts

Solids and turnings never share a drum

Solids are whole pieces: bar ends, plate offcuts, rejected parts. Turnings are the chips and curls a lathe or mill cuts off. USGS says new superalloy scrap comes as solids, turnings or grindings, and that by volume turnings are the largest quantity.

Blame the buy-to-fly ratio, aerospace's measure of metal bought against finished part weight. USGS says superalloy buy-to-fly ratios run from under 5:1 to over 20:1 depending on the part, with a 1998 average of about 7:1. At 7:1, six of every seven pounds bought end up as scrap, much of it as chips, so the turnings drums deserve the same care as the solids.

Mixing the forms causes trouble both ways: solids get buried in chips, and chips cling to solids. In USGS's tungsten study (2000 data), scrap processors collected superalloy turnings and qualitatively verified their chemical purity, which is far simpler when a drum holds one alloy. Keep a solids bin, a turnings drum and a grindings pail per alloy.

Sources: USGS Circular 1196-A-M: metal recycling in the United States; USGS Circular 1196-R: tungsten recycling in the United States in 2000.

Oil, coolant and water add weight that is not metal

Turnings come off the machine wet, and a scale counts the fluid along with the metal. ReMA's published grades show how the trade treats it: yellow brass rod turnings should not contain over 3% free iron, oil or other moisture; mixed aluminum turnings are subject to deductions for dirt, free iron, oil and moisture; mixed Monel turnings are graded on nickel content on a dry basis. A quote is for the metal, not the fluid.

  • Drain turnings before they go in the drum, in a basket over a tray or a drum with a drain.
  • Keep lids on outdoors; rain turns dry turnings wet.
  • Do not hose turnings to clean them. That trades oil for water.
  • Keep rags, gloves, broken tools and inserts out of chip drums.
  • Keep steel chips out, too. OSHA's scrap recycling guidance notes that ferrous metals are magnetic, and we do not buy iron or steel, so pass a magnet over a drum before you seal it. The exception is pure nickel and some Monel 400, which respond to a magnet themselves: the Nickel 200 bulletin lists magnetic properties, and the Monel 400 bulletin says some heats are magnetic at room temperature.

Sources: ReMA ISRI Specifications (July 2026); OSHA 3348: metal scrap recycling; Special Metals: Nickel 200 bulletin; Special Metals: MONEL alloy 400 bulletin.

Beryllium copper: its own bin, and OSHA's rules

Beryllium copper is a copper alloy, not a superalloy, but it lives in the same industries. OSHA says beryllium-copper alloys go into switches in automobiles, computers, radar, satellite and telecommunications equipment, and lists beryllium use in aerospace, electronics, energy, telecommunications, medical and defense work. The Copper Development Association lists C17200 as a wrought copper beryllium alloy in its high copper alloys group.

  • OSHA says employees exposed to beryllium are at risk of chronic beryllium disease and lung cancer; the permissible exposure limit in 29 CFR 1910.1024 is 0.2 micrograms per cubic meter of air as an 8-hour time-weighted average.
  • Machining, grinding, cutting or sanding an item that contains beryllium is processing under OSHA's standard and falls outside its exemption for articles.
  • Material for disposal, recycling or reuse that contains at least 0.1 percent beryllium, or is beryllium-contaminated, must be labeled under the Hazard Communication standard.

OSHA's guide gives the business reason as well: "Beryllium scrap should be kept segregated from other metals because of its higher value as a recyclable material when compared to mixed metal alloys." Give it a labeled container, do not cut or grind pieces to fit, and name it in your quote notes. Label it at the machine, too, because EPA Method 6200 lists beryllium among the light elements that field portable XRF cannot detect. We buy it along with the other nonferrous metals.

Sources: OSHA: beryllium standard small entity compliance guide; 29 CFR 1910.1024, beryllium (Cornell LII); Copper Development Association: C17200; EPA Method 6200 (field portable XRF).

Labels, paperwork and photos before the pickup

A drum label needs four things: the alloy, the form, the condition and a rough weight, written like 625 turnings, drained, two drums. Keep mill certificates and job travelers with the solids they belong to; a heat number or UNS number on a cert beats anything you can see. For pieces with no paperwork, identify the metal before it goes in a drum.

It helps at the sale as well. California's purchase record describes the material, and AB 476 (2025), as the Senate Public Safety Committee described it, adds the weight and any engraved or etched marks or serial numbers.

For a quote, photograph each container from above with its label showing, then a handful of pieces up close, and send them with the alloys and rough weights through the quote form or to help@socalscrapmetalbuyer.com. We buy every metal except iron and steel, and the pickup is free anywhere in Southern California, including Los Angeles, Orange, Riverside, San Bernardino, San Diego, Ventura and Imperial counties.

Sources: California Attorney General Information Bulletin 2025-DLE-12; Senate Public Safety Committee analysis of AB 476 (2025).

Common questions

Is high temp alloy scrap the same thing as superalloy scrap?

Close enough in a shop. Both names cover the nickel, cobalt and iron-based alloys made to hold their strength when hot. Sort by the alloy name on the job paperwork either way, not by the family.

Do two nickel alloys really need two drums?

Yes. Two nickel alloys can differ widely in chromium, cobalt, molybdenum, iron and tungsten, and a drum holding both matches neither. One alloy per drum is what lets the scrap go back into its own alloy.

What do I do with turnings that already got mixed?

Stop adding to that drum, mark it mixed, and write down which alloys went in. Photograph it and say so in the quote notes; a mixed drum can still be quoted, as a mix.

Is exotic metal recycling worth the sorting in a small shop?

Sorting is mostly habit: a labeled bin at each machine and a rule that chips go in the bin for the alloy being cut. Lots kept that way can be quoted as what they are, and the pickup is free anywhere in Southern California.

Does beryllium copper need special handling before pickup?

Keep it in its own labeled container, do not cut or grind it to fit, and name it in the quote notes. The beryllium copper section above covers OSHA's rules.

Have metal to sell?

Send a few photos and a rough weight for a quote. Free pickup anywhere in Southern California. Every metal except iron and steel.

Call nowGet a quote